Upgrading an old Hornby Pannier

GWR Pannier engines are the best. They’re my favourite locos and I  have quite a few, in both OO and N gauge. The Hornby versions are great little incarnations and with a few upgrades, they can be made even better.

The Hornby R041 57xx class is one of my top model trains and I’m always on the lookout for additional good priced second-hand models to join my collection.

And when getting new ones there are a couple of things that I always do to improve their running quality.

The first thing is to replace the motor.

The R041 was originally fitted with a 3-pole X03 or X04 DC motor. These have proved reliable but swapping them out for five-pole versions gives smoother operation, better low-speed control and improved pulling power. If you’re unfamiliar with the workings of DC motors, there’s a good introduction here.

Suitable five-pole variants of X03 or X04 motors are available on eBay for around £20 to £39. (The X04 differs in having a brass worm gear instead of the nylon variant in the 03 version).

Fitting these is time-consuming but straightforward.

First, the body shell is removed. On the R041, this is achieved by undoing a single screw under the water tank, on one side and towards the front. The plastic shell can then be slid back (clear of two plastic tabs at the front) and removed.

With the shell off, the existing motor can be extracted.

At the rear of the motor is a screw that holds it in place. Locate this and remove it. The motor should then pop off – it needs lifting off diagonally so the worm gear can come from of the cog to which it connects.

The wires from the wheel pick-ups can then be unsoldered to detach the motor in its entirety from the chassis.

A much better magnet

Before swapping the new motor in, extra oomph is be added by upgrading its magnet with a Neodymium replacement. (Suitable magnets for the X03/04 can be purchased from first4magnets.

The magnet is a metal cube located at the rear of the motor. Usually, this is held in place by a screw on the top that passes through the outer frame, through the centre of the magnet and secured in place by a nut underneath.  Undo this and pull the magnet free. Position the new Neodymium magnet and put the screw back in.

Back to the replacement motor. Position the new 5-pole motor in place and reconnect the rear screw before soldering the wire from the pickups into place.

With this done, I use a toothpick to clear out any debris in the worm gear and then lubricate the lower cog, worm gear and wheel rods with my preferred oil.

I then give it a test run to check everything works as it should.

Assuming this is the case, the body shell can be reattached and the loco set off with its new improved pulling power and slow-running capability to join its brothers and sisters on my layout.


> A final, personal, note: I spend a huge amount of time testing, photographing, writing and researching techniques for these articles and pay for all the running costs of MRE out of my own pocket. If you found this article useful you can support me by making a donation on my fund-raising page. Thanks and happy modelling, Andy.
Founder of ModelRailwayEngineer, Andy Leaning

Andy is a lifelong modeler, writer, and founder of modelrailwayengineer.com. He has been building model railways, dioramas, and miniatures for over 20 years. His passion for model making and railways began when he was a child, building his first layout at the age of seven.
Andy’s particular passion is making scenery and structures in 4mm scale, which he sells commercially. He is particularly interested in modelling the railways of South West England during the late Victorian/early Edwardian era, although he also enjoys making sci-fi and fantasy figures and dioramas. His website has won several awards, and he is a member of MERG (Model Railway Electronics Group) and the 009 Society.
When not making models, Andy lives in Surrey with his wife and teenage son. Other interests include history, science fiction, photography, and programming. Read more about Andy.

Afflliate disclosure:The links on this page may take you to carefully selected businesses, such as Hornby, Amazon, eBay and Scale Model Scenery, where you can purchase the product under affiliate programmes. This means I receive a small commission on any orders placed although the price you pay does not change. You can read my full affiliate policy here. I also sell my my own ready to use, pre-made and painted buildings and terrain features. browse the range.
2 comments
  1. Hi Andy,
    Excellent explanation of ‘what to do’. Could you let me know what the part number is for the neodymium magnet is from first4magnets please. I looked at their web site, but failed to find anything appropriate.
    Many thanks,
    John Harper

Add Comment

Required fields are marked *. Your email address will not be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.